| Pad Wear Sensor Included | No |
| Caliper Type | Fixed |
| Caliper Casting Material | Cast Iron |
| Bleeder Screw Included | Yes |
| Is Prop Sixty Five Affected | No |
| Is the item CARB affected | No |
| Abutment Clips Included | No |
| Anti-Rattle Spring Included | Yes |
| Piston Size (OD) (in) | 1.415 |
| Inlet Fitting Type | Inverted Flare |
| FAQs | What type of grease is used on floating caliper mounting pins? |
| Is Or Contains A Battery | No |
| Inlet Port Size | 10.00366 |
| Product Condition | Remanufactured |
| Dust Boots Included | Yes |
| Installation Hardware Included | Yes |
| Color | Gray |
| FAA_A6 | A silicone grease is used on floating caliper mounting pins. |
| FAA_A7 | New hardware is included with all of our Calipers however the mounting bracket is an added option depending on part number and application. Mounting Brackets are also sold separately for most applications. |
| Contains Electronic Components? | No |
| FAA_A4 | Brake squeal can be caused by improper installation of the brake pads, improperly installed brake hardware and improper brake rotor finish. |
| FAA_A5 | A symptom of a low brake pedal is usually caused by air in the system, misadjusted rear brake shoes, deteriorated brake hose(s) or a defective master cylinder. |
| FAA_A2 | As a rule, always use brake fluid recommended by O.E. The fluid type is stamped on the master cylinder reservoir lid. Always use new fluid in a sealed container. |
| FAA_A3 | Inspect both calipers for binding or sticky slides or pins. Also ensure that brake hoses are not collapsed or restricted and inspect steering/suspension components for proper operation. |
| FAA_A1 | Not recommended. The O.E. manufacturers specified steel or phenolic pistons based on the intended use of the vehicle. It is recommended that the installer follow the manufacturer's recommendations. |
| Piston Size (OD) (mm) | 35.94 |
| Prop 65 | NO |
| Bleeder Thread Size | M8x1.25 |
| Piston Material | Steel |
| Caliper Slides Included | No |
| E-Waste | No |
| Is Item A Chemical | No |
| Piston Quantity | 2 |
| Bleeder Port Size | M8x1.25 |
| FAQ_Q5 | Could calipers be the cause of a low brake pedal? |
| FAQ_Q4 | Brakes squeal all of the time. What's causing the squeal? |
| Casting Number | 36/290 |
| Features and Benefits | Rubber seals are replaced with new high temperature EPDM rubber for extended life and optimum performance. |
| Pads Included | No |
| Programming Required | No |
| Is or contains a bulb? | No |
| FAQ_Q7 | Do all of your Calipers come with the new hardware and a mounting bracket for installation? |
| Mounting Bolts Included | No |
| FAQ_Q6 | What type of grease is used on floating caliper mounting pins? |
| FAQ_Q1 | Can I switch out a Phenolic Piston Caliper for a Steel Piston Caliper or vice versa? |
| FAQ_Q3 | Car pulls to one side during braking. Why? |
| FAQ_Q2 | What type of fluid should I use: DOT 3, DOT 4, or DOT 5? |
| Piston Diameter | 1.415 |
| Mounting Bracket Included | No |
| Mounting Hole Diameter | 10.156 |
| Package Contents | Caliper; Instruction Sheet; Hardware Kit |
| Inlet Thread Size | M10X1.0 |
| Does it require SDS | No |
| First Application Year | 1996 |
| Mounting Bolt Included | No |
| Is item a chemical? | No |
| SDS Required | No |
| Brake Piston Count | 2 |
| Brake Caliper Finish | Oil Emulsion |
| Bracket Included | No |
| Is the item CARB affected? | No |
| Caliper Color | Gray |
| Mounting Hardware Included | Yes |
| Is Or Contains A Bulb | No |
| Rust Resistant Coating | Yes |
| Mounting Hole Thread Diameter | 10.156 |
| Is or contains a battery? | No |
| Bleeder Screw Cap Included | No |
| Contains Electronic Components | No |
| Grade Type | Regular |
| Part Terminology | Disc Brake Caliper |
